3D Printed Graphene Aerogel May Lead to Powerful Supercapacitors

IMTS

Share this Article

Supercapacitors are energy storage devices that charge very rapidly and can retain their storage capacity through tens of thousands of charge cycles. Their applications include regenerative braking systems in electric vehicles. They hold less energy in the same amount of space as batteries, and they don’t hold a charge for quite as long – but advances in supercapacitor technology could make them competitive with batteries in a wider range of applications. In a study entitled “Efficient 3D Printed Pseudocapacitive Electrodes with Ultrahigh MnO2 Loading,” a group of researchers at UC Santa Cruz and Lawrence Livermore National Laboratory have achieved unprecedented performance from a supercapacitor electrode. The electrode was fabricated from a 3D printable graphene aerogel, which was used to build a porous 3D scaffold loaded with pseudocapacative material.

In tests, the electrodes achieved the highest areal capacitance ever reported for a supercapacitor. In an earlier study, the researchers achieved extremely fast supercapacitor electrodes 3D printed from graphene aerogel. This time, they used an improved graphene aerogel to build a porous scaffold which was loaded with manganese oxide.

A pseudocapacitor is a type of supercapacitor that stores energy through a reaction at the electrode surface, giving it more battery-like performance than supercapacitors that store energy primarily through an electrostatic mechanism (called electric double-layer capacitance, or EDLC).

“The problem for pseudocapacitors is that when you increase the thickness of the electrode, the capacitance decreases rapidly because of sluggish ion diffusion in bulk structure,” said UC Santa Cruz Professor of Chemistry and Biochemistry Yat Li. “So the challenge is to increase the mass loading of pseudocapacitor material without sacrificing its energy storage capacity per unit mass or volume.”

The study demonstrates a breakthrough in balancing mass loading and capacitance in a pseudocapacitor. The researchers increased mass loading to record levels of more than 100 milligrams of manganese oxide per square centimeter without compromising performance, a major increase compared to commercial devices, which have levels of about 10 milligrams per square centimeter.

The areal capacitance also increased linearly with mass loading of manganese oxide and electrode thickness, while the capacitance per gram (gravimetric capacitance) remained almost unchanged. This indicates that the electrode’s performance is not limited by ion diffusion even at such a high mass loading.

In the traditional fabrication of supercapacitors, according to graduate student Bin Lao, a thin coating of electrode material is applied to a thin metal sheet that serves as a current collector. Increasing the thickness of the coating causes performance to decline, so multiple sheets are stacked to build capacitance, increasing weight and material cost.

“With our approach, we don’t need stacking because we can increase capacitance by making the electrode thicker without sacrificing performance,” Yao said.

The researchers managed to increase the thickness of the electrodes to four millimeters without sacrificing performance. The electrodes were designed with a periodic pore structure that allows for both uniform deposition of the material and efficient ion distribution for charging and discharging. The printed structure itself is a lattice made from cylindrical porous rods of the graphene aerogel. Manganese oxide is then deposited onto the lattice.

“The key innovation in this study is the use of 3D printing to fabricate a rationally designed structure providing a carbon scaffold to support the pseudocapacitive material,” Li said. “These findings validate a new approach to fabricating energy storage devices using 3D printing.”

Supercapacitor devices made with the electrodes showed good cycling stability, retaining more than 90 percent of initial capacitance after 20,000 cycles of charging and discharging. The 3D printed electrodes allow for a large amount of design flexibility, and the graphene-based inks offer ultrahigh surface area, lightweight properties, elasticity, and superior electrical conductivity.

Authors of the paper include Bin Yao, Swetha Chandrasekaran, Jing Zhang, Wang Xiao, Fang Qian, Cheng Zhu, Eric B. Duoss, Christopher M. Spadaccini, Marcus A. Worsley and Yat Li.

Discuss this and other 3D printing topics at 3DPrintBoard.com or share your thoughts below. 

 

Share this Article


Recent News

Will There Be a Desktop Manufacturing Revolution outside of 3D Printing?

Know Your Würth: CEO AJ Strandquist on How Würth Additive Can Change 3D Printing



Categories

3D Design

3D Printed Art

3D Printed Food

3D Printed Guns


You May Also Like

Featured

Pressing Refresh: What CEO Brad Kreger and Velo3D Have Learned About Running a 3D Printing Company

To whatever extent a business is successful thanks to specialization, businesses will nonetheless always be holistic entities. A company isn’t a bunch of compartments that all happen to share the...

Würth Additive Launches Digital Inventory Services Platform Driven by 3D Printing

Last week, at the Additive Manufacturing Users’ Group (AMUG) Conference in Chicago (March 10-14), Würth Additive Group (WAG) launched its new inventory management platform, Digital Inventory Services (DIS). WAG is...

Featured

Hypersonic Heats Up: CEO Joe Laurienti on the Success of Ursa Major’s 3D Printed Engine

“It’s only been about 24 hours now, so I’m still digesting it,” Joe Laurienti said. But even via Zoom, it was easy to notice that the CEO was satisfied. The...

Featured

3D Printing’s Next Generation of Leadership: A Conversation with Additive Minds’ Dr. Gregory Hayes

It’s easy to forget sometimes that social media isn’t reality. So, at the end of 2023, when a burst of doom and gloom started to spread across the Western world’s...